Irrigation Syringe Manufacturers

What We Manufacture in the Irrigation Syringe Range

An irrigation syringe is a high-volume syringe, typically 60 ml, used to flush wounds, remove earwax or deliver enteral formula and fluids through a feeding tube. The wide-bore outlet and large barrel allow a high flow rate at controlled pressure, which is why these syringes are specified separately from standard injection syringes. Our wholesale Irrigation Syringe manufacturers range is built around that clinical function.

We supply four configurations from the current catalogue, each aimed at a different point in the postoperative nutrition and wound-care workflow.

Application Fit Across Postoperative Nutrition and Wound Care

Irrigation and feeding syringes sit at the interface between the clinician, the feeding tube or wound bed and the fluid being delivered. The choice of barrel size, tip geometry and connector therefore follows the application rather than a single universal specification.

• Enteral feeding: 60 ml enteral-only syringes with screw caps for formula delivery and water flushes through nasogastric, gastrostomy and jejunostomy tubes.
• Oral and nasal feeding: small-capacity syringes for controlled doses in neonatal and paediatric care.
• Wound and cavity irrigation: high-volume syringes used to flush debris and exudate from wounds, supported by our Wound Dressing range where the irrigation step is part of a dressing protocol.
• Ear and canal irrigation: large-barrel syringes with a directed tip for controlled flushing.
• General flushing: catheter, drain and line flushing where a wide-bore, low-resistance flow path is preferred.

Specification Variables We Confirm Before Production

Because irrigation syringes are used in direct contact with patients and with enteral feeding systems, the specification is agreed line by line before tooling or production begins. The table below shows the variables we work through with each customer.

Materials, Flow Behaviour and Accuracy

Irrigation and feeding syringes are moulded from medical-grade polymers selected for clarity, dimensional stability and compatibility with enteral formula and irrigation solutions. The plunger seal is designed to give a smooth, low-resistance stroke so the clinician can control flow by hand without excessive force. Where a customer requires latex-free construction or a specific colour code, we confirm that at the specification stage.

Accuracy in this product family is about repeatable graduation and consistent barrel bore rather than fine injection tolerance. We control wall thickness, tip concentricity and graduation alignment so that the delivered volume corresponds to the printed scale across the production run.

OEM/ODM Configuration and Private Label

We operate as an OEM/ODM irrigation syringe factory, so the range can be adapted to a customer's own brand and market requirements. Configuration work typically covers barrel colour, graduation layout, connector type, plunger style, pouch printing and carton design. Our in-house design and tooling capability means the syringe body, cap and adapter can be developed as a matched set rather than assembled from unrelated parts.

• Custom barrel colour and colour-coding for enteral-only identification
• Choice of screw cap, transfer adapter or ring-pull tip
• Private-label pouch, carton and leaflet artwork
• Sample rounds for fit, feel and graduation review before mass production

Quality Control and Compliance

Our Suzhou factories operate under ISO 13485:2016 quality management, with inspection procedures applied from incoming material through moulding, assembly and packaging. Most of our products are CE certified, and our Suzhou factories comply with FDA requirements. For irrigation syringes, the inspection points that matter most are barrel dimensions, tip and connector fit, graduation legibility, plunger stroke and packaging integrity.

We maintain sample retention and traceability records so that a delivered batch can be traced back to its production run. Where a customer's market requires specific documentation, we confirm the applicable compliance evidence during the quotation stage.

Related Products in Our Postoperative Nutrition and Medical Consumables Range

Irrigation syringes are supplied alongside the wider consumables we manufacture, which allows a distributor or hospital group to consolidate several product lines in one programme.

• Medical Tape for securing feeding tubes, dressings and lines
• Sterile Wound Dressing for the dressing step after wound irrigation
• Jumbo Raw Material Roll for customers who convert their own medical materials

Information We Use to Configure Your Solution

To prepare a suitable irrigation syringe specification and quotation, we work from the clinical and commercial requirements of the project. The following inputs allow us to propose the right barrel size, connector and packaging without unnecessary iteration.

• Intended application: enteral feeding, oral/nasal feeding, wound irrigation or general flushing
• Required capacity and graduation range
• Feeding tube or connection type the syringe must mate with
• Sterile or non-sterile presentation and packaging format
• Branding requirements, including pouch and carton artwork
• Target market and any documentation the market requires
• Estimated order quantity per specification and delivery schedule

Frequently Asked Questions

What sizes of irrigation syringe does ADVAN Medical manufacture?

Our range includes small-capacity oral/nasal feeding syringes, 60 ml color-coded enteral-only syringes with screw caps, large-capacity hand-push feeding syringes with adapters and ring-pull feeding syringes with transfer adapters. We confirm the exact capacity and graduation during specification.

Can you supply irrigation syringes under our own brand?

Yes. We provide OEM/ODM and private-label production, covering barrel colour, graduation layout, connector type, pouch printing and carton design. Sample rounds are available so the fit, feel and graduation can be reviewed before mass production.

Are your irrigation syringes compatible with enteral feeding tubes?

We supply screw cap, transfer adapter and ring-pull tip configurations, and can match the connector to the feeding tube system used in your market. Confirming the tube interface at the enquiry stage avoids connection mismatch later.

What quality standards apply to your irrigation syringe production?

Our Suzhou factories operate under ISO 13485:2016 quality management, and most of our products are CE certified. Our Suzhou factories comply with FDA requirements. Inspection covers barrel dimensions, connector fit, graduation legibility and packaging integrity, with sample retention and traceability records.

What is the minimum order quantity for irrigation syringes?

Minimum order quantity depends on the specification, packaging and branding requirements. We support both large-volume and small-batch orders across our three factories, and confirm the applicable MOQ when the specification is agreed.

Do you supply irrigation syringes outside China?

Yes. We have exported medical consumables to more than 60 countries, including Southeast Asia, Africa, the Middle East, Eastern Europe, Russia, South America and Oceania. Our customers include hospitals, medical distributors and retailer shops.